|
|
Polaris Ranger XP HD EV RZR RZRS RZR4 Crew, Yamaha Rhino, Kawasaki Mule Teryx, Arctic Cat Prowler
|
|
|
|
|
|
|
Hello and Welcome to
EZ Turn Signal Kits & Accessories
|
|
|
|
|
|
|
Hello, my name is Cisco Folk and I am the President of EZ Turn Signal Kits & Accessories here in Glendale, AZ. My passion is the outdoors, so I purchased a 2006 Polaris Ranger XP to help me get around.
After a few years of using the old hang your arm out the side to signal on coming traffic, I decided I had enough. I wanted to install LED turn signals for my added safety. When I tried to purchase a four light LED turn signal kit, I was unable to find anyone who had developed a LED Turn Signal Kit. As we all know the UTV's have small batteries and small charging systems and the main reasons why I wanted all 4 turn signal lights to be LED are:
- Less current draw, resulting in increased battery & alternator life while allowing more power for other vehicle requirements.
- Faster illumination offers significant safety benefits for following drivers to react quicker, resulting in an average of three foot reaction time advantage for every 10 miles per hour.
- LEDs have no filament, therefore are not susceptible to shock & vibration, a major cause of failure for lamps with incandescent bulbs.
|
|
|
So, I created my own LED Turn Signal Kit. I wanted DOT approved, good looking, clean and crisp LED lights, ones that were very visible, even during the day. The LED Lights in my (stock# 105) kit are not only 16 light emitting diodes each, but they are hard wired with encapsulated electronics to eliminate corrosion. They have both the black (+) and white (-) wires to make a great connection, no screw through a metal surface to the frame for ground. You can hard wire the lights to both positive and ground, so you always have a good connection.
|
|
|
|
The Turn Signal Switch is heavy duty, has the right and left turn signals along with a pull out flare tab for the 4-way emergency (hazard warning) flashers. I added an 18" black ground wire with ring tong connector, this easily installs using one of the mounting screws that holds the turn signal switch to your steering column. This makes a great ground, so you don't have to scrape on your new recreational vehicle steering column.
I designed and developed a custom turn signal switch (TSS) mounting strap for the 2009-2011 Polaris Ranger XP/HD and 2010-2011 Ranger 800 Crew models. This professional looking mount will allow full range of motion and clearance for the tilt steering wheel.
|
|
|
I designed and developed a custom turn signal switch (TSS) mounting plate for the 2010-2011 Polaris Ranger EV and 400 models. This professional looking black powder coated plate looks and works great on the Ranger's.
|
|
|
I have seen several turn signal switches out there that come with a hose clamp, not this company. You will always get good looking, high quality turn signals from EZ Turn Signal Kits!
|
|
The LED Electronic Flasher is the key to the entire kit. This special LED electronic flasher is quiet, no annoying clicking sounds.
I was the first to develop and market the LED Turn Signal Kits, for all of the UTV side-by-sides! These kits can be easily installed on any side-by-side, UTV, Golf Cart, Club Car, Sand Car, Dune Buggy, etc.
|
|
See our entire stock of turn signal kits listed below and if you have any questions, please contact us, we are here to help you!
- The original LED Turn Signal Kit (stock# 105)
- The LED Parking Lights & Turn Signal Kit (stock# 107)
- The SM LED Turn Signal Kit (stock# 104)
- The Regular Bulb Turn Signal Kit (stock# 103)
|
|
|
|
|
The LED Turn Signal Kit will fit all years for the Polaris Ranger XP / HD / EV / TM / 400 / 425 / 500 / 700 / 800 / RZR / RZRS / RZR4 and Crew, all years for the Yamaha Rhino, all years for the Kawasaki Teryx & Mule, and all years for the Arctic Cat Prowler. (SEE NOTES BELOW) This kit can be easily installed on any Side-by-Side (side x side), UTV, Golf Cart, Club Car, Sand Car, Dune Buggy, etc.
Note: some like amber lights front and rear, order from the drop down box (BELOW) a) Light Options: Amber Kit: All 4 Amber lights.
|
|
Note: the 2009-2011 Polaris Ranger XP / HD and the 2010-2011 Ranger 800 Crew use our custom turn signal switch (TSS) mounting strap. This custom strap will allow the tilt steering to have full range of motion with the turn signal switch mounted just under the steering wheel. Order from the drop down box (BELOW) b) TurnSignal Switch: 09-11 Ranger XP/HD (TSS) Strap or 10-11 Ranger 800 Crew (TSS) Strap.
Note: the 2010-2011 Polaris Ranger EV & 400 use our custom turn signal switch (TSS) mounting plate. This custom plate was designed to mount the turn signal switch below the steering wheel on the plastic shroud. Order from the drop down box (BELOW) b) TurnSignal Switch: 10-11 Ranger EV/400 (TSS) Plate. This custom (TSS) mounting plate is only available on the LED turn signal kits.
Note: the 2008-2011 Arctic Cat Prowler with tilt steering, you may want to use a 5" inch hose clamp to mount the turn signal switch.
Note: the 2010-2011 Kawasaki Teryx with the plastic shroud molded up to the steering wheel, you will need to cut some of the plastic to make room for mounting the turn signal switch OR use a 5" inch hose clamp around the plastic shroud.
|
|
|
|
|
|
|
|
|
ALL KITS: In Stock & Ready to Ship!
|
|
|
|
This is a 12 volt LED Turn Signal Kit with 2 Amber (front) and 2 Red (rear) DOT approved LED lights. The 4 LED light kit comes with a turn signal switch, which has a pilot light for the turn signals and 4-way emergency flashers (hazard warning). The turn signal switch has a pull on flare tab for the 4-way hazard lights, an added 18" ground wire (for better grounding of the turn signal switch) and the hardware to mount it to your steering column.
The four LED Lights are 4”x 2” rectangular with 16 (LED) Light Emitting Diodes each, polycarbonate lens & housing and hard wired with encapsulated electronics to eliminate corrosion.
The special LED Electronic Flasher has the 3 pin connections for LOAD, PILOT and POWER. This special electronic LED flasher is also quite, no annoying clicking sounds.
The kit includes: 2 Amber and 2 Red DOT approved LED lights, the Turn Signal Switch with an extra 18” ground wire with ring tong connector (for better grounding of the turn signal switch) and the hardware to mount it to your steering column, the special LED Electronic Flasher, an in-line fuse holder, a 3 amp fuse, the self tapping screws for mounting the lights and flasher, the mounting installation instructions, the wiring instructions & diagram, and all the help and support you need from EZ Turn Signal Kits.
This kit can be easily installed, it does not go into any factory wiring, and it is a completely independent system that comes with the wiring diagram and instructions. Each wire has a different color and the wiring diagram shows where each colored wire goes. I include my phone number and e-mail address with the instructions, so if you have any questions about your installation you can contact me.
This kit was originally developed for my 2006 Polaris Ranger XP and my customers have installed their kits on the Polaris Ranger 425 / TM / 500 / 700 / 800 / XP / HD, Razor (RZR RZRS RZR4) and Crew, the Yamaha Rhino, the Kawasaki Mule and Teryx, and the Arctic Cat Prowler. This kit can be easily installed on any 12 volt Side-by-Side, UTV, Golf Cart, Club Car, Sand Car, Dune Buggy, etc.
This turn signal switch has been installed on thousands of units, very nice and easy to operate. The Motor Vehicle Department and your local police departments will be impressed. Everyone who rides on the street, off road, at the dunes or in congested riding areas, should have turn signals for there added safety.
|
|
|
Total Power Draw: .32 amps - that's less than a third of an amp with the four hazard lights on!
|
|
|
|
|
|
|
|
|
2 - Amber 4" x 2" LED Lights
2 - Red 4" x 2" LED Lights
1 - Turn Signal Switch
|
|
1 - LED Flasher
1 - ATC Fuse Holder
1 - ATC 3 Amp Fuse
|
|
Hardware for mounting components
Mounting Installation Instructions
Wiring Instructions & Diagram
|
|
|
Options: We have some Custom Kit Brackets along with a Wire & Connector Kit that you may want to use with your Turn Signal Kit. Any of these options purchased with your kit, will save you money!
|
|
|
|
 
|
LED Parking Lights
& Turn Signal Kit
|
|
|
LED Parking Lights
& Turn Signal Kit
|
|
|
The LED Parking Lights & Turn Signal Kit will fit all years for the Polaris Ranger XP / HD / EV / TM / 400 / 425 / 500 / 700 / 800 / RZR / RZRS / RZR4 and Crew, all years for the Yamaha Rhino, all years for the Kawasaki Teryx & Mule, and all years for the Arctic Cat Prowler. (SEE NOTES BELOW) This kit can be easily installed on any Side-by-Side (side x side), UTV, Golf Cart, Club Car, Sand Car, Dune Buggy, etc.
Note: some like amber lights front and rear, order from the drop down box (BELOW) a) Light Options: Amber Kit: All 4 Amber lights.
|
|
Note: the 2009-2011 Polaris Ranger XP / HD and the 2010-2011 Ranger 800 Crew use our custom turn signal switch (TSS) mounting strap. This custom strap will allow the tilt steering to have full range of motion with the turn signal switch mounted just under the steering wheel. Order from the drop down box (BELOW) b) TurnSignal Switch: 09-11 Ranger XP/HD (TSS) Strap or 10-11 Ranger 800 Crew (TSS) Strap.
Note: the 2010-2011 Polaris Ranger EV & 400 use our custom turn signal switch (TSS) mounting plate. This custom plate was designed to mount the turn signal switch below the steering wheel on the plastic shroud. Order from the drop down box (BELOW) b) TurnSignal Switch: 10-11 Ranger EV/400 (TSS) Plate. This custom (TSS) mounting plate is only available on the LED turn signal kits.
Note: the 2008-2011 Arctic Cat Prowler with tilt steering, you may want to use a 5" inch hose clamp to mount the turn signal switch.
Note: the 2010-2011 Kawasaki Teryx with the plastic shroud molded up to the steering wheel, you will need to cut some of the plastic to make room for mounting the turn signal switch OR use a 5" inch hose clamp around the plastic shroud.
|
|
|
|
|
|
|
|
|
ALL KITS: In Stock & Ready to Ship!
|
|
|
|
This is a 12 volt LED Parking Lights and Turn Signal Kit with 2 Amber (front) and 2 Red (rear) Dual Mode DOT approved LED lights. The 4 Dual Mode LED light kit comes with a turn signal switch, which has a pilot light for the turn signals and 4-way emergency flashers (hazard warning). The turn signal switch has a pull on flare tab for the 4-way hazard lights, an added 18" ground wire (for better grounding of the turn signal switch) and the hardware to mount it to your steering column.
The four Dual Mode LED Lights are 4”x 2” rectangular with 12 Colored (red or amber) Light Emitting Diodes each. They are chrome based, come with both clear & colored lenses and are hard wired with encapsulated electronics to eliminate corrosion. They have 3 lead wires each, one for ground, normal mode (parking lights) and high mode (turn signals), which is equal to 24 LED’s on high mode.
The special LED Electronic Flasher has the 3 pin connections for LOAD, PILOT and POWER. This special electronic LED flasher is also quite, no annoying clicking sounds.
The Parking Light Switch is a LED illuminated rocker switch and is easy to install, vibration resistance, and will illuminate when turned on.
The kit includes: 2 Amber and 2 Red Dual Mode DOT approved LED lights with both colored and clear lenses, the Turn Signal Switch with an extra 18” ground wire with ring tong connector (for better grounding of the turn signal switch) and the hardware to mount it to your steering column, the special LED Electronic Flasher, the LED illuminated rocker switch for parking lights, an in-line fuse holder, a 3 amp fuse, the self tapping screws for mounting the lights and flasher, the mounting installation instructions, the wiring instructions & diagram, and all the help and support you need from EZ Turn Signal Kits.
This kit can be easily installed, it does not go into any factory wiring, and it is a completely independent system that comes with the wiring diagram and instructions. Each wire has a different color and the wiring diagram shows where each colored wire goes. I include my phone number and e-mail address with the instructions, so if you have any questions about your installation you can contact me.
This kit was originally developed for my 2009 Polaris Ranger XP and my customers have installed their kits on the Polaris Ranger 425 / TM / 500 / 700 / 800 / XP / HD, Razor (RZR RZRS RZR4) and Crew, the Yamaha Rhino, the Kawasaki Mule and Teryx, and the Arctic Cat Prowler. This kit can be easily installed on any 12 volt Side-by-Side, UTV, Golf Cart, Club Car, Sand Car, Dune Buggy, etc.
This turn signal switch has been installed on thousands of units, very nice and easy to operate. The Motor Vehicle Department and your local police departments will be impressed. Everyone who rides on the street, off road, at the dunes or in congested riding areas, should have turn signals for there added safety.
|
|
|
Total Power Draw: .84 amps - that's less than an amp with the four parking and hazard lights on!
|
|
|
<<< hold mouse over pictures to see other examples >>>
|
|
|
|
|
|
|
|
2 - Amber 4"x2" DM LED Lights
2 - Red 4"x2" DM LED Lights
1 - Turn Signal Switch
|
|
1 - LED Flasher
1 - Fuse Holder & Fuse
1 - LED Rocker Switch
|
|
Hardware for mounting components
Mounting Installation Instructions
Wiring Instructions & Diagram
|
|
|
Options: We have some Custom Kit Brackets along with a Wire & Connector Kit that you may want to use with your Turn Signal Kit. Any of these options purchased with your kit, will save you money!
|
|
|
|
|
|
|
|
The SM LED Turn Signal Kit will fit all years for the Polaris RZR, RZRS, RZR4, Ranger XP, HD, Crew, EV, 400, 500, 700 & 800, all years for the Yamaha Rhino 700, 660 & 450, all years for the Kawasaki Teryx & Mule, and all years for the Arctic Cat Prowler. (SEE NOTES BELOW) This kit can be easily installed on any Side-by-Side (side x side), Golf Cart, Sand Car, etc.
Note: some like to customize their UTV with Double or Triple lights, order from the drop down box (BELOW) a) Light Options: Double Lights: 4 Amber & 4 Red lights or Triple Lights: 6 Amber & 6 Red lights.
Note: some like amber lights front and rear, order from the drop down box (BELOW) a) Light Options: Amber Kit: All 4 Amber lights or Double Lights All Amber: 8 Amber lights or Triple Lights All Amber: 12 Amber lights.
|
|
Note: the 2009-2011 Polaris Ranger XP / HD and the 2010-2011 Ranger 800 Crew use our custom turn signal switch (TSS) mounting strap. This custom strap will allow the tilt steering to have full range of motion with the turn signal switch mounted just under the steering wheel. Order from the drop down box (BELOW) b) TurnSignal Switch: 09-11 Ranger XP/HD (TSS) Strap or 10-11 Ranger 800 Crew (TSS) Strap.
Note: the 2010-2011 Polaris Ranger EV & 400 use our custom turn signal switch (TSS) mounting plate. This custom plate was designed to mount the turn signal switch below the steering wheel on the plastic shroud. Order from the drop down box (BELOW) b) TurnSignal Switch: 10-11 Ranger EV/400 (TSS) Plate. This custom (TSS) mounting plate is only available on the LED turn signal kits.
Note: the 2008-2011 Arctic Cat Prowler with tilt steering, you may want to use a 5" inch hose clamp to mount the turn signal switch.
Note: the 2010-2011 Kawasaki Teryx with the plastic shroud molded up to the steering wheel, you will need to cut some of the plastic to make room for mounting the turn signal switch OR use a 5" inch hose clamp around the plastic shroud.
|
|
|
|
|
|
|
|
|
ALL KITS: In Stock & Ready to Ship!
|
|
|
|
This is a 12 volt Surface Mount LED Turn Signal Kit with 2 Surface Mounted ¾” inch Amber (front) and 2 Surface Mounted ¾” inch Red (rear) Super Bright DOT approved LED lights (no brackets required). The SM LED light kit comes with a turn signal switch, which has a pilot light for the turn signals and 4-way emergency flashers (hazard warning). The turn signal switch has a pull on flare tab for the 4-way hazard lights, an added 18" ground wire (for better grounding of the turn signal switch) and the hardware to mount it to your steering column.
The 4 Surface Mounted LED super bright lights are ¾” inch round with an attached rubber grommet for quick mounting. They are surface mounted LED’s with a slim-line design for mounting in small spaces (no brackets required). These SM LED’s are DOT approved, meet the P2PC requirements for 45 degree mounting and provide superior light output. They have a Space Saving Design, Hi Impact Acrylic Lens and Housing and are hard wired with Completely Resin Sealed Electronics to eliminate corrosion.
The Special LED Electronic Flasher has the 3 pin connections for LOAD, PILOT and POWER. This special electronic LED flasher is also quite, no annoying clicking sounds.
The kit includes: 2 Amber and 2 Red SM LED super bright lights with grommets, the Turn Signal Switch with an extra 18” ground wire with ring tong connector (for better grounding of the turn signal switch) and the hardware to mount it to your steering column, the special LED Electronic Flasher with mounting hardware, an ATC in-line fuse holder, a 3 amp fuse, the mounting installation instructions, the wiring instructions & diagram, and all the help and support you need from EZ Turn Signal Kits.
This kit can be easily installed, you don’t need any brackets for mounting lights, it does not go into any factory wiring, and it is a completely independent system that comes with the wiring diagram and instructions. Each wire has a different color and the wiring diagram shows where each colored wire goes. I include my phone number and e-mail address with the instructions, so if you have any questions about your installation you can contact me.
This kit was originally developed for the Polaris RZR, RZRS, RZR4 and Ranger EV. My customers have installed their kits on the Polaris Ranger EV XP HD RZR, RZRS, RZR4 & Crew, the Yamaha Rhino, the Kawasaki Mule & Teryx, and the Arctic Cat Prowler. This kit can be easily installed on any 12 volt Side-by-Side UTV, Golf Cart, Club Car, Sand Car, Dune Buggy, etc.
This turn signal switch has been installed on thousands of units, very nice and easy to operate. The Motor Vehicle Department and your local police departments will be impressed. Everyone who rides on the street, off road, at the dunes or in congested riding areas, should have turn signals for there added safety.
|
|
|
Total Power Draw: .20 amps - that's less than a quarter of an amp with the four hazard lights on!
|
|
|
<<< hold mouse over pictures to see other examples >>>
|
|
|
|
|
|
|
|
|
|
|
|
2 – Amber SM LED Lights
2 – Red SM LED Lights
1 - Turn Signal Switch
|
|
1 - LED Flasher
1 - ATC Fuse Holder
1 - ATC 3 Amp Fuse
|
|
Hardware for mounting components
Mounting Installation Instructions
Wiring Instructions & Diagram
|
|
|
Options: We have a Wire & Connector Kit that you may want to use with your Turn Signal Kit.
- If you don’t have your own Wire and Connectors, this kit will make it easy to connect up your turn signals.
|
|
|
|
|
|
|
Regular Bulb Turn Signal Kit
|
|
|
|
Regular Bulb Turn Signal Kit
|
|
|
The Regular Bulb Turn Signal Kit will fit all years for the Polaris Ranger XP / HD / TM / 425 / 500 / 700 / 800 / RZR / RZRS / RZR4 and Crew, all years for the Yamaha Rhino, all years for the Kawasaki Teryx & Mule, and all years for the Arctic Cat Prowler. (SEE NOTES BELOW) This kit can be easily installed on any Side-by-Side (side x side), UTV, Golf Cart, Club Car, Sand Car, Dune Buggy, etc.
Note: some like amber lights front and rear, order from the drop down box (BELOW) a) Light Options: Amber Kit: All 4 Amber lights.
|
|
Note: the 2009-2011 Polaris Ranger XP / HD and the 2010-2011 Ranger 800 Crew use our custom turn signal switch (TSS) mounting strap. This custom strap will allow the tilt steering to have full range of motion with the turn signal switch mounted just under the steering wheel. Order from the drop down box (BELOW) b) TurnSignal Switch: 09-11 Ranger XP/HD (TSS) Strap or 10-11 Ranger 800 Crew (TSS) Strap.
Note: the 2010-2011 Polaris Ranger EV & 400 use our custom turn signal switch (TSS) mounting plate. This custom plate was designed to mount the turn signal switch below the steering wheel on the plastic shroud. Order from the drop down box (BELOW) b) TurnSignal Switch: 10-11 Ranger EV/400 (TSS) Plate. This custom (TSS) mounting plate is only available on the LED turn signal kits.
Note: the 2008-2011 Arctic Cat Prowler with tilt steering, you may want to use a 5" inch hose clamp to mount the turn signal switch.
Note: the 2010-2011 Kawasaki Teryx with the plastic shroud molded up to the steering wheel, you will need to cut some of the plastic to make room for mounting the turn signal switch OR use a 5" inch hose clamp around the plastic shroud.
|
|
|
|
|
|
|
|
|
ALL KITS: In Stock & Ready to Ship!
|
|
|
|
This is a 12 volt Regular Bulb Turn Signal Kit with 2 Amber (front) and 2 Red (rear) DOT approved Regular Bulb lights. The 4 Regular Bulb light kit comes with a turn signal switch, which has a pilot light for the turn signals and 4-way emergency flashers (hazard warning). The turn signal switch has a pull on flare tab for the 4-way hazard lights, an added 18" ground wire (for better grounding of the turn signal switch) and the hardware to mount it to your steering column.
The four Regular Bulb Lights are 4”x 2” rectangular with (2) bulbs each, they have two stainless steel grounds, corrosion-resistant contacts, lubricated fleet service bulbs, corrosion-proof body; they come with 4 extra ground wires and 8 self tapping screws for mounting.
The Bulb Flasher has the 3 pin connections for LOAD, PILOT and POWER. This flasher comes with a clamp and a self tapping screw for mounting.
The kit includes: 2 Amber and 2 Red DOT approved Regular Bulb lights, 4 ground wires with ring tong connectors (for grounding the regular lights), the Turn Signal Switch with an extra 18” ground wire with ring tong connector (for better grounding of the turn signal switch) and the hardware to mount it to your steering column, the Flasher with mounting clamp, an in-line fuse holder, a 5 amp fuse, the self tapping screws for mounting the lights and flasher, the mounting installation instructions, the wiring instructions & diagram, and all the help and support you need from EZ Turn Signal Kits.
This kit can be easily installed, it does not go into any factory wiring, and it is a completely independent system that comes with the wiring diagram and instructions. Each wire has a different color and the wiring diagram shows where each colored wire goes. I include my phone number and e-mail address with the instructions, so if you have any questions about your installation you can contact me.
My customers have installed their kits on the Polaris Ranger 425 / TM / 500 / 700 / 800 / XP / HD, Razor (RZR RZRS RZR4) and Crew, the Yamaha Rhino, the Kawasaki Mule and Teryx, and the Arctic Cat Prowler. This kit can be easily installed on any 12 volt Side-by-Side, UTV, Golf Cart, Club Car, Sand Car, Dune Buggy, etc.
This turn signal switch has been installed on thousands of units, very nice and easy to operate. The Motor Vehicle Department and your local police departments will be impressed. Everyone who rides on the street, off road, at the dunes or in congested riding areas, should have turn signals for there added safety.
|
|
|
Total Power Draw: 2.65 amps with the four hazard lights on!
|
|
|
|
|
|
|
|
2 - Amber 4"x2" REG Bulb Lights
2 - Red 4"x2" REG Bulb Lights
1 - Turn Signal Switch
|
|
1 - Regular Flasher
1 - ATC Fuse Holder
1 - ATC 5 Amp Fuse
|
|
Hardware for mounting components
Mounting Installation Instructions
Wiring Instructions & Diagram
|
|
|
Options: We have some Custom Kit Brackets along with a Wire & Connector Kit that you may want to use with your Turn Signal Kit. Any of these options purchased with your kit, will save you money!
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For more information:
EZ Turn Signal Kits
P. O. Box 1818
Glendale, AZ 85311-1818 US
E-mail: Cisco@LEDTSK.com
Phone: (623) 435-1337
Phone: (928) 369-2892
|
|
|
|
|
|
|
|
|
